Alzheimers Disease

Aluminium in drinking water: A risk of Alzheimer’s disease? Every year, about 200,000 people in Germany suffer from this disease. And the incidence of dementia is growing with the increasing life expectancy of the population. It amounts to only about one thousandth, at sixty it is old already at 45 percent. Main charges will be made in addition to the food via the drinking water after drinking water regulation, and the drinking water standards of WHO, EU is a limit of 0.2 mg per liter, which may not be exceeded if the water is to be used as drinking water. This one assumes that only large amounts of aluminum have an impact on our health. But also the small, continuous intake of aluminum leads to a rising concentration of aluminium in the brain and thus to the risk of disease. A study by the Institut national de la sante et de la recherche MEDICALE in Bordeaux documented that already the daily dose of 0.1 mg aluminium restricts our cognitive abilities.

How reliably protect from aluminum in drinking water? The tap water with the water softening before treated and then reverse osmosis is generally prepared for pure, will water. It removes the germs, pesticides, herbicides, hydrocarbons and salinity. Reverse osmosis does but not sufficient protect against aluminum – deposits in the brain. On the contrary. Reverse osmosis water is acidic and not suitable for human consumption, because the nerve-damaging aluminium has the ability to accumulate in the body. Suitability of water in relation to the purification of reading in ppm measured in mS/cm for the detoxification and excretion 0-70 great 0-140 moderately suitable for the detoxification and drainage suitable 70 125 140 250 no longer sufficient for the detoxification and excretion 125 250 250 500 no detoxifying and out-conductive properties more available 250 600 500 1200 water can deposit in the body lead to > 600 > 1200 only through a thorough cleaning of the tap water with reverse osmosis, for example with the triwaclean ro, as well as a treatment, for example with the triwaclean stage AquPlus, reaches the purified water a pH of 9-9.5. Thus, it neutralizes the excess acids in the body and the aluminum can no longer accumulate.

Review Rails

As long as a nursing bed is converted, it is to shut down as much as possible. The connection to the mains power supply is recommended only for electric settings. A daily use can only happen if the electrician on the spot does a daily check of propulsion systems. To guarantee of the electrical safety of the nursing bed, finally three more test steps should be made: transportation of the bed the power cord on the floor may fall and be overrun, therefore a device must exist, which prevents the comprehensive description of all maintenance and care measures (here is not an indication of standards) check primary fuse on the transformer (this is non-existent or defective, is a retrofit) other defects and damage, which should arise and therefore also be part of the review of care beds, are recommended: kink protection and strain relief are missing or defective slatted frame is broken side rail beams lift cylinder housing of the remote control are broken using an inappropriate mattress damage the housing of the control unit / motor is defective or gas springs are defective end position cut-off emergency lowering is defective, clipping the side rails is broken is broken besides the clipping, as mentioned in the last item in this list, there are many more sources of error in the side rails. This can cause bad jamming and crushing. Therefore are dependent on the expected mechanical load, to comply strictly with the prescribed separation distance and mass.

All locking and fastening elements must be functional. The State of the page grid is therefore an important part of regular checks. The audit involves Following: distances between the moving parts must be within the normal range of finger check for additional damage, weak spots, signs of overuse review of suspensions and latches for damage or wear locking mechanism which has side rails work comply with the given Seitengittermasse; Review by: distance between side rails in upright position and elements in their environment of thickness of the mattress proper distance between Head / footboard and side rails proper distance between split side rails corresponds to intended use and manufacturer’s specifications and bed in flat position measurements of the length of the side rail or sum of all lengths of split side rails on one side of the beds must be correct height of the upper edge of the side rail above the mattress (no compression) smallest dimension of all available openings between the side rails and bed surface must not be exceeded are all these distances and dimensions are given accurate and may be exceeded no more than 10 per cent.